CIP Level 2 NACE-CIP2-001 Practice Test Engine: Try These 100 Exam Questions
Guaranteed Success in CIP Level 2 NACE-CIP2-001 Exam Dumps
NACE-CIP2-001 Exam is a rigorous test that requires candidates to have a strong understanding of the principles and practices of corrosion control and coatings. To be eligible to take the exam, candidates must have at least two years of experience in the field and have completed the NACE-CIP1 (Coating Inspector Level 1) Exam. Candidates who pass the NACE-CIP2-001 Exam will be awarded the Coating Inspector Level 2 certification, which is recognized by employers and industry professionals worldwide.
NEW QUESTION # 18
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Scarifiers
- B. Water Jetting Equipment
- C. Abrasive Blasting Equipment
- D. Power Tools
Answer: B
NEW QUESTION # 19
Linings are used on the interior of pipelines to
- A. provide protection against soil chemicals.
- B. afford limited temperature insulation.
- C. reduce magnetic polarity.
- D. protect the transported product.
Answer: D
NEW QUESTION # 20
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. False
- B. True
Answer: B
NEW QUESTION # 21
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. mixed with uncontaminated abrasive
- B. disposed of properly.
- C. washed with clean potable water prior to Use.
- D. run through the air wash separator.
Answer: B
NEW QUESTION # 22
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. Concrete
- B. 2-Layet Polyethylene (PE)
- C. 3-Layet Polyethylene (PE)
- D. Coal Tar Enamel
Answer: A
NEW QUESTION # 23
When observing design defects the NACE Inspector should:
- A. Ignore the defect as the inspector can't change the design
- B. Request that the item be rebuilt with a better design for coating
- C. Stop the job immediately
- D. Document the defect and the potential problems that could result
Answer: D
NEW QUESTION # 24
When conducting inspections the Inspector should follow which standards:
- A. Australian standards in Australia
- B. The specified standards
- C. ISO standards in Europe and Asia
- D. NACE and SSPC standards in North America
Answer: B
NEW QUESTION # 25
Galvanizing performs best in which of the following exposures:
- A. pH above 12
- B. pH below 4
- C. pH between 5-10
- D. pH of 13
Answer: C
NEW QUESTION # 26
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Redo the pre-cleaning based on the other inspectors results
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Advise the other inspector he is using an incorrect method
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION # 27
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 single rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 50 double rubs with a saturated cloth.
- D. 25 double rubs with a saturated cloth.
Answer: C
NEW QUESTION # 28
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that another NACE Inspector would understand
- B. Language that only in the project would understand
- C. Language that the most would understand
- D. Language that only technical experts would understand
Answer: C
NEW QUESTION # 29
Coating Surveys are legally required:
- A. On high pressure gas lines and fireproofed structures
- B. On food and beverage vessels and can linings
- C. On commercial marine vessels and offshore platforms
- D. On water tanks and potable water pipelines
Answer: C
NEW QUESTION # 30
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Gathering
- C. Distribution
- D. Transmission
Answer: C
NEW QUESTION # 31
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by SP 3
- C. SP 1 followed by acid etching
- D. SP 1 followed by SP 2
Answer: D
NEW QUESTION # 32
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. urethanes.
- C. powder coatings.
- D. inorganic zincs.
Answer: D
NEW QUESTION # 33
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection only
- B. Visual inspection and Non-destructive testing
- C. Visual inspection, Non-Destructive and Destructive testing
- D. All types of inspection without supervision
Answer: C
NEW QUESTION # 34
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower its temperature
- B. raise its relative humidity.
- C. lower its dew point,
- D. provide worker comfort.
Answer: C
NEW QUESTION # 35
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. High Voltage DC Constant Current
- B. High Voltage DC Pulse Type
- C. High Voltage AC
- D. Low Voltage Sponge Type
Answer: A
NEW QUESTION # 36
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Document the readings at the end of the shift
- B. Check to See if the dehumidification equipment is operating correctly
- C. Call your supervisor
- D. Advise the coating applicator supervisor of your readings
Answer: D
NEW QUESTION # 37
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Mandatory
- B. Consensus
- C. Voluntary
- D. De facto
Answer: C
NEW QUESTION # 38
Antifouling coatings are regulated by international treaties.
- A. False
- B. True
Answer: B
NEW QUESTION # 39
An Inspection and Test Plan is required when:
- A. When the Owner specifies one
- B. When the Inspector requests one
- C. It is always required
- D. When the Coating Applicator requests one
Answer: C
NEW QUESTION # 40
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. Cold flow or creep
- B. A very low reading
- C. A very high reading
- D. No difference from any other coating
Answer: A
NEW QUESTION # 41
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Mainline coating
- D. Areas exposed to Ultra Violet light
Answer: B
NEW QUESTION # 42
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION # 43
......
Test Engine to Practice NACE-CIP2-001 Test Questions: https://vce4exams.practicevce.com/NACE/NACE-CIP2-001-practice-exam-dumps.html